Code: Select all
System: Kernel: 5.10.0-9-amd64 x86_64 bits: 64 compiler: gcc v: 10.2.1 Desktop: Cinnamon 4.8.6
Distro: Debian GNU/Linux 11 (bullseye)
Network: Device-1: Ralink RT5390 Wireless 802.11n 1T/1R PCIe driver: rt2800pci v: 2.3.0 port: e000 bus ID: 06:00.0
IF: wlp6s0 state: down mac: <filter>
Device-2: Realtek RTL8111/8168/8411 PCI Express Gigabit Ethernet vendor: Hewlett-Packard driver: r8169 v: kernel
port: d000 bus ID: 07:00.0
IF: enp7s0 state: up speed: 1000 Mbps duplex: full mac: <filter>
2. I did successfully install the realtec driver for RTL8111/8168/8411 PCI Express Gigabit Ethernet
3. just to make sure I reinstalled initramfs-tools ( firmware for Realtek Ethernet, wifi and Bluetooth adapters supported by various drivers)
4. did sudo apt install -y firmware-realtek
Code: Select all
majpooper@1150z:~$ sudo apt install -y firmware-realtek
Reading package lists... Done
Building dependency tree... Done
Reading state information... Done
firmware-realtek is already the newest version (20210315-3).
0 upgraded, 0 newly installed, 0 to remove and 0 not upgraded.Code: Select all
majpooper@1150z:~$ sudo dmesg
[ 5.834720] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[ 5.834743] rt2800pci 0000:06:00.0: firmware: failed to load rt2860.bin (-2)
[ 5.834746] firmware_class: See https://wiki.debian.org/Firmware for information about missing firmware
[ 5.834748] rt2800pci 0000:06:00.0: Direct firmware load for rt2860.bin failed with error -2
[ 5.835246] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[ 5.835258] rt2800pci 0000:06:00.0: firmware: failed to load rt2860.bin (-2)
[ 5.835260] rt2800pci 0000:06:00.0: Direct firmware load for rt2860.bin failed with error -2
[ 5.848532] audit: type=1400 audit(1634409334.017:21): apparmor="DENIED" operation="capable" profile="/usr/sbin/cups-browsed" pid=843 comm="cups-browsed" capability=23 capname="sys_nice"
[ 8.054195] usb 2-2: 3:1: cannot get freq at ep 0x84
[ 8.126242] usb 2-2: 3:1: cannot get freq at ep 0x84
[ 8.605094] r8169 0000:07:00.0 enp7s0: Link is Up - 1Gbps/Full - flow control rx/tx
[ 8.605114] IPv6: ADDRCONF(NETDEV_CHANGE): enp7s0: link becomes ready
[ 13.604812] sdg: sdg1
[ 13.639465] sd 7:0:0:0: [sdg] Attached SCSI disk
[ 13.639728] ses 7:0:0:1: Attached Enclosure device
[ 38.889856] FAT-fs (sdh1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 38.900484] FAT-fs (sdj1): Volume was not properly unmounted. Some data may be corrupt. Please run fsck.
[ 38.949495] EXT4-fs (sdi1): mounted filesystem with ordered data mode. Opts: (null)
[ 38.988525] EXT4-fs (sdk1): mounted filesystem with ordered data mode. Opts: (null)
[ 39.007603] EXT4-fs (sdk2): mounted filesystem with ordered data mode. Opts: (null)
[ 64.966445] ieee80211 phy0: rt2x00lib_request_firmware: Info - Loading firmware file 'rt2860.bin'
[ 64.966482] rt2800pci 0000:06:00.0: firmware: failed to load rt2860.bin (-2)
[ 64.966490] rt2800pci 0000:06:00.0: Direct firmware load for rt2860.bin failed with error -2
